ddrinit: d56ea12 Ranks: 1 Die size: 0 Rank size: 13 MB Full size: 13 MB Full SDRAM Width: 0 bits Primary SDRAM Width: 0 bits ECC SDRAM Width: 0 bits Device Width: 16 bits Number of Row Addresses: 32768 Number of Column Addresses: 1024 Number of Bank Addresses: 8 Bank Group Addressing: 1 Clock Cycle Time (tCK): 1876 ps Minimum Clock Cycle Time (tCK min): 0 ps Maximum Clock Cycle Time (tCK max): 0 ps CAS# Latency Time (tAA min): 37520 ps Minimum Four Activate Windows Delay (tFAW): 41272 ps RAS to CAS Delay Time (tRCD min): 18760 ps Row Precharge Delay Time (tRP min): 18760 ps Active to Precharge Delay Time (tRAS min): 43148 ps Normal Refresh Recovery Delay Time (tRFC1 min): 0 ps 2x Mode Refresh Recovery Delay Time (tRFC2 min): 0 ps 4x Mode Refresh Recovery Delay Time (tRFC4 min): 0 ps Short Row Active to Row Active Delay (tRRD_S min): 11256 ps Long Row Active to Row Active Delay (tRRD_L min): 0 ps Long CAS to CAS Delay Time (tCCD_L min): 0 ps Minimum Active to Auto-Refresh Delay (tRC): 60032 ps DDRMC0: Initialized successfully within 1417848 us, 1 ranks, speed 1066 MT/s Ranks: 1 Die size: 0 Rank size: 13 MB Full size: 13 MB Full SDRAM Width: 0 bits Primary SDRAM Width: 0 bits ECC SDRAM Width: 0 bits Device Width: 16 bits Number of Row Addresses: 32768 Number of Column Addresses: 1024 Number of Bank Addresses: 8 Bank Group Addressing: 1 Clock Cycle Time (tCK): 1876 ps Minimum Clock Cycle Time (tCK min): 0 ps Maximum Clock Cycle Time (tCK max): 0 ps CAS# Latency Time (tAA min): 37520 ps Minimum Four Activate Windows Delay (tFAW): 41272 ps RAS to CAS Delay Time (tRCD min): 18760 ps Row Precharge Delay Time (tRP min): 18760 ps Active to Precharge Delay Time (tRAS min): 43148 ps Normal Refresh Recovery Delay Time (tRFC1 min): 0 ps 2x Mode Refresh Recovery Delay Time (tRFC2 min): 0 ps 4x Mode Refresh Recovery Delay Time (tRFC4 min): 0 ps Short Row Active to Row Active Delay (tRRD_S min): 11256 ps Long Row Active to Row Active Delay (tRRD_L min): 0 ps Long CAS to CAS Delay Time (tCCD_L min): 0 ps Minimum Active to Auto-Refresh Delay (tRC): 60032 ps DDRMC1: Initialized successfully within 1407992 us, 1 ranks, speed 1066 MT/s Total DDR memory size 2048 MiB Memory interleaving: 4 KiB, 2-channel NOTICE: BL31: v2.6(release):v2.5-887-g9566c09d4 NOTICE: BL31: Built : 12:17:21, Feb 2 2023 U-Boot 2021.01-00012-gc358b4cc0b (May 02 2024 - 21:30:00 +0000) Model: RanetkaPC SBC v1.1 DRAM: 1.3 GiB CPU: Setting CPU frequency to 1188000000 (PLL mult: 43)...done. drivers/i2c/designware_i2c.c:779-designware_i2c_ofdata_to_platdata() i2c_designware i2c@1730000: Can't get reset: -2 Timed out waiting for bus PMIC: Failed to read digipot, ret: -121 PMIC: Failed to set core voltage, ret: -121, digipot addr: 0x2c drivers/i2c/designware_i2c.c:779-designware_i2c_ofdata_to_platdata() i2c_designware i2c@1710000: Can't get reset: -2 Timed out waiting for bus HDMI: Failed to read adv7513, ret: -121 HDMI: Failed to poweron adv7513, ret: -121, addr: 0x3d WDT: Started with servicing (120s timeout) MMC: sdhci0@10220000: 0, sdhci1@10230000: 1 Loading Environment from SPIFlash... SF: Detected w25q128fw with page size 256 Bytes, erase size 4 KiB, total 16 MiB OK Display: Arm Mali DP550 r0p2 malidp_setup_timings: product = DP550, reg_val = 0x10031050, HSYNCPOL = 2, VSYNCPOL = 8 display_enable: panel_bpp = 8, timing.hactive = 800, timing.vactive = 600, pixelclock = 49500000 Display-bmp: 800 x 600 with 1 colours, display bpix 32 In: serial0@1750000 Out: serial Err: serial Net: Warning: ethernet@10200000 (eth0) using random MAC address - 46:cf:5b:21:bf:f3 eth0: ethernet@10200000 Hit any key to stop autoboot: 0 Setting bus to 3 Error writing the chip: -121 unable to select a mode : -110 mmc_init: -524, time 209 38151 mcom03-RanetkaPC_Module-1.3.dtb 14211080 Image 132150 splash.bmp 35424 mcom03-bub-r1.3.0.dtb 36925 mcom03-RanetkaPC_Module-1.5.dtb 39238 mcom03-RanetkaPC_TestJig-1.3.dtb 28960 coremark.exe 29456 coremark-mt.exe 1536138 splash_tribar.bmp 385146 splash_controlpanel.bmp 12962268 initrd.img 27540 coremark-arm32.exe 29116 coremark-arm32-mt.exe 38896 mcom03-RanetkaPC_TestJig-1.3-noemmc.dtb 1920138 splash_tribar_800x600.bmp 23096 stream_c_arm64.exe 39758 mcom03-RanetkaPC_SBC-1.1.dtb 39758 mcom03-RanetkaPC_SBC-1.1.dtb.good 36137 mcom03-KERAutomation-Q7-1.2.dtb 19 file(s), 0 dir(s) Trying to boot from eMMC 36137 bytes read in 24 ms (1.4 MiB/s) 14211080 bytes read in 3726 ms (3.6 MiB/s) 12962268 bytes read in 3404 ms (3.6 MiB/s) Moving Image from 0x892400000 to 0x892480000, end=893266000 ## Flattened Device Tree blob at 898c00000 Booting using the fdt blob at 0x898c00000 Loading Ramdisk to 89dd51000, end 89ea51000 ... OK Loading Device Tree to 000000089dd45000, end 000000089dd50d28 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 4.19.106-g1aec3ec6b (rz@devbox) (gcc version 8.2.1 20180802 (GNU Toolchain for the A-profile Architecture 8.2-2018-08 (arm-rel-8.23))) #244 SMP Sun Apr 21 19:47:29 UTC 2024 [ 0.000000] Machine model: MCom-03 KERAutomation Q7 Module v1.2 [ 0.000000] earlycon: uart0 at MMIO32 0x0000000001750000 (options '115200n8') [ 0.000000] bootconsole [uart0] enabled [ 0.000000] cma: Reserved 128 MiB at 0x00000008d8000000 [ 0.000000] On node 0 totalpages: 327680 [ 0.000000] DMA32 zone: 5120 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 327680 pages, LIFO batch:63 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] random: get_random_bytes called from start_kernel+0xa0/0x44c with crng_init=0 [ 0.000000] percpu: Embedded 22 pages/cpu s51672 r8192 d30248 u90112 [ 0.000000] pcpu-alloc: s51672 r8192 d30248 u90112 alloc=22*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 322560 [ 0.000000] Kernel command line: console=ttyS0,115200 consoleblank=0 vt.global_cursor_default=0 vt.cur_default=1 earlyprintk=ttyS0,115200 earlycon splash plymouth.ignore-serial-consoles root=/dev/mmcblk1p2 rootwait ro fsck.mode=auto fsck.repair=yes init=/sbin/init rdinit=/init loglevel=8 net.ifnames=0 fbcon=logo-pos:center fbcon=logo-count:1 video=HDMI-A-1:800x600@75 [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Memory: 1115392K/1310720K available (8766K kernel code, 1206K rwdata, 3020K rodata, 832K init, 329K bss, 64256K reserved, 131072K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 29904 entries in 117 pages [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] ITS: No ITS available, not enabling LPIs [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000001180000 [ 0.000000] arch_timer: cp15 timer(s) running at 27.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x63a1e71a3, max_idle_ns: 440795203123 ns [ 0.000003] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 4398046511093ns [ 0.009253] Console: colour dummy device 80x25 [ 0.014162] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=270000) [ 0.025507] pid_max: default: 32768 minimum: 301 [ 0.030707] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.038066] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.047418] ASID allocator initialised with 32768 entries [ 0.053447] rcu: Hierarchical SRCU implementation. [ 0.060691] smp: Bringing up secondary CPUs ... [ 0.076155] Detected VIPT I-cache on CPU1 [ 0.076192] GICv3: CPU1: found redistributor 1 region 0:0x00000000011a0000 [ 0.076238] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.086805] Detected VIPT I-cache on CPU2 [ 0.090623] GICv3: CPU2: found redistributor 2 region 0:0x00000000011c0000 [ 0.090646] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.101150] Detected VIPT I-cache on CPU3 [ 0.108179] GICv3: CPU3: found redistributor 3 region 0:0x00000000011e0000 [ 0.108202] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.108276] smp: Brought up 1 node, 4 CPUs [ 0.157993] SMP: Total of 4 processors activated. [ 0.163138] CPU features: detected: GIC system register CPU interface [ 0.170192] CPU features: detected: 32-bit EL0 Support [ 0.176147] CPU: All CPU(s) started at EL2 [ 0.180675] alternatives: patching kernel code [ 0.186766] devtmpfs: initialized [ 0.197067] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.207863] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.218958] pinctrl core: initialized pinctrl subsystem [ 0.225478] NET: Registered protocol family 16 [ 0.230907] audit: initializing netlink subsys (disabled) [ 0.237036] audit: type=2000 audit(0.180:1): state=initialized audit_enabled=0 res=1 [ 0.245552] cpuidle: using governor menu [ 0.250132] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.259369] DMA: preallocated 256 KiB pool for atomic allocations [ 0.268322] mcom03-media-pinctrl 1320000.urb:media-pinctrl: 15 pins & 1 groups registered [ 0.278770] mcom03-lsperiph-pinctrl 1680000.urb:lsperiph0-pinctrl: 32 pins & 0 groups registered [ 0.289937] mcom03-hsperiph-pinctrl 10400000.urb:hsperiph-pinctrl: 91 pins & 23 groups registered [ 0.302024] mcom03-lsperiph-pinctrl 17e0000.urb:lsperiph1-pinctrl: 32 pins & 1 groups registered [ 0.317658] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.325468] cryptd: max_cpu_qlen set to 1000 [ 0.330947] vgaarb: loaded [ 0.334123] SCSI subsystem initialized [ 0.338385] libata version 3.00 loaded. [ 0.342741] usbcore: registered new interface driver usbfs [ 0.348779] usbcore: registered new interface driver hub [ 0.354647] usbcore: registered new device driver usb [ 0.361670] clocksource: Switched to clocksource arch_sys_counter [ 0.436859] NET: Registered protocol family 2 [ 0.442208] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes) [ 0.450802] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.458851] TCP bind hash table entries: 16384 (order: 6, 262144 bytes) [ 0.466502] TCP: Hash tables configured (established 16384 bind 16384) [ 0.473834] UDP hash table entries: 1024 (order: 3, 32768 bytes) [ 0.480443] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) [ 0.487668] NET: Registered protocol family 1 [ 0.492839] RPC: Registered named UNIX socket transport module. [ 0.499315] RPC: Registered udp transport module. [ 0.504482] RPC: Registered tcp transport module. [ 0.509626] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.516699] PCI: CLS 0 bytes, default 64 [ 0.521177] Unpacking initramfs... [ 1.044228] Initramfs unpacking failed: junk in compressed archive [ 1.060681] Freeing initrd memory: 13312K [ 1.066070] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 1.079138] Initialise system trusted keyrings [ 1.084581] workingset: timestamp_bits=46 max_order=19 bucket_order=0 [ 1.097325] NFS: Registering the id_resolver key type [ 1.102954] Key type id_resolver registered [ 1.107527] Key type id_legacy registered [ 1.113275] Key type asymmetric registered [ 1.117755] Asymmetric key parser 'x509' registered [ 1.123167] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 1.131263] io scheduler noop registered [ 1.135566] io scheduler deadline registered [ 1.140318] io scheduler cfq registered (default) [ 1.145475] io scheduler mq-deadline registered [ 1.150430] io scheduler kyber registered [ 1.155339] irq_elvees_qlic 1940000.interrupt-controller: Reset targets according to mask 0x10000 [ 1.165260] irq_elvees_qlic 1940000.interrupt-controller: Initialized successfully [ 1.174645] gpio-dwapb 1610000.gpio: initialized pinmux driver for port A [ 1.182407] gpio-dwapb 1610000.gpio: initialized pinmux driver for port B [ 1.190088] gpio-dwapb 1610000.gpio: initialized pinmux driver for port C [ 1.197824] gpio-dwapb 1610000.gpio: initialized pinmux driver for port D [ 1.206309] gpio-dwapb 1780000.gpio: initialized pinmux driver for port A [ 1.213985] gpio-dwapb 1780000.gpio: initialized pinmux driver for port B [ 1.221643] gpio-dwapb 1780000.gpio: initialized pinmux driver for port C [ 1.229331] gpio-dwapb 1780000.gpio: initialized pinmux driver for port D [ 1.237176] mcom-pwm 1770000.pwm: elvees,output-channel DT property missing [ 1.244813] mcom-pwm 1770000.pwm: elvees,state-on-disable DT property missing [ 1.253090] mcom03-pcie 2000000.pcie: Failed to get PCIe resets [ 1.259702] misc dmabuf: /dev/dmabuf ready [ 1.265141] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.273383] 1640000.serial0: ttyS1 at MMIO 0x1640000 (irq = 12, base_baud = 843750) is a 16550A [ 1.283480] 1650000.serial0: ttyS2 at MMIO 0x1650000 (irq = 13, base_baud = 843750) is a 16550A [ 1.293633] 1750000.serial0: ttyS0 at MMIO 0x1750000 (irq = 23, base_baud = 1745028) is a 16550A [ 1.303338] console [ttyS0] enabled [ 1.303338] console [ttyS0] enabled [ 1.311166] bootconsole [uart0] disabled [ 1.311166] bootconsole [uart0] disabled [ 1.323951] libphy: Fixed MDIO Bus: probed [ 1.329390] (unnamed net_device) (uninitialized): Using gen_pool sram-pool for DMA descriptors [ 1.329409] arasan-gemac 10200000.ethernet (unnamed net_device) (uninitialized): Using random hw address [ 1.360055] arasan-gemac 10200000.ethernet eth0: Arasan GEMAC Ethernet at 0x10200000 int=14 (d6:f6:d0:75:06:57) [ 1.371468] usbcore: registered new interface driver r8152 [ 1.382616] dwc3 10000000.dwc3: Failed to get clk 'ref': -2 [ 1.394107] dwc3 10100000.dwc3: Failed to get clk 'ref': -2 [ 1.401283] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.407449] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 1.416505] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe6d hci version 0x110 quirks 0x0000000000010010 [ 1.427056] xhci-hcd xhci-hcd.0.auto: irq 56, io mem 0x10000000 [ 1.434050] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 1.443299] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.451368] usb usb1: Product: xHCI Host Controller [ 1.456828] usb usb1: Manufacturer: Linux 4.19.106-g1aec3ec6b xhci-hcd [ 1.464130] usb usb1: SerialNumber: xhci-hcd.0.auto [ 1.470028] hub 1-0:1.0: USB hub found [ 1.474261] hub 1-0:1.0: 1 port detected [ 1.478931] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.485081] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 1.493662] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 1.501019] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.510192] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19 [ 1.519442] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.527524] usb usb2: Product: xHCI Host Controller [ 1.532984] usb usb2: Manufacturer: Linux 4.19.106-g1aec3ec6b xhci-hcd [ 1.540276] usb usb2: SerialNumber: xhci-hcd.0.auto [ 1.546061] hub 2-0:1.0: USB hub found [ 1.550272] hub 2-0:1.0: 1 port detected [ 1.555003] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.561139] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 1.570156] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe6d hci version 0x110 quirks 0x0000000000010010 [ 1.580715] xhci-hcd xhci-hcd.1.auto: irq 57, io mem 0x10100000 [ 1.587634] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 1.596890] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.604977] usb usb3: Product: xHCI Host Controller [ 1.610426] usb usb3: Manufacturer: Linux 4.19.106-g1aec3ec6b xhci-hcd [ 1.617729] usb usb3: SerialNumber: xhci-hcd.1.auto [ 1.623489] hub 3-0:1.0: USB hub found [ 1.627699] hub 3-0:1.0: 1 port detected [ 1.632347] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.638480] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 1.647057] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 1.654423] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.663599] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19 [ 1.672848] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.680916] usb usb4: Product: xHCI Host Controller [ 1.686376] usb usb4: Manufacturer: Linux 4.19.106-g1aec3ec6b xhci-hcd [ 1.693679] usb usb4: SerialNumber: xhci-hcd.1.auto [ 1.699476] hub 4-0:1.0: USB hub found [ 1.703704] hub 4-0:1.0: 1 port detected [ 1.708411] usbcore: registered new interface driver uas [ 1.714457] usbcore: registered new interface driver usb-storage [ 1.721332] i2c /dev entries driver [ 1.725386] mr75202 1f050000.pvt: Configure TS SDA clock: 1031250 Hz, div = 24 [ 1.733558] mr75202 1f050000.pvt: 4 temperature sensors [ 1.740699] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 1188000 KHz [ 1.749009] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 1188000000 (-34) [ 1.758802] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1161000 KHz [ 1.768746] sdhci: Secure Digital Host Controller Interface driver [ 1.775672] sdhci: Copyright(c) Pierre Ossman [ 1.780538] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.787143] mcom03-hsperiph-pinctrl 10400000.urb:hsperiph-pinctrl: [sdmmc0_ctrl] group doesn't support property 9 [ 1.798631] mcom03-hsperiph-pinctrl 10400000.urb:hsperiph-pinctrl: pin_config_group_set op failed for group 0 [ 1.809723] sdhci-arasan 10220000.sdhci0: Error applying setting, reverse things back [ 1.850131] mmc0: SDHCI controller on 10220000.sdhci0 [10220000.sdhci0] using ADMA 64-bit [ 1.859928] mcom03-hsperiph-pinctrl 10400000.urb:hsperiph-pinctrl: [sdmmc1_ctrl] group doesn't support property 9 [ 1.871488] mcom03-hsperiph-pinctrl 10400000.urb:hsperiph-pinctrl: pin_config_group_set op failed for group 1 [ 1.882627] sdhci-arasan 10230000.sdhci1: Error applying setting, reverse things back [ 1.911377] mmc0: new HS200 MMC card at address 0001 [ 1.918179] mmcblk0: mmc0:0001 M65704 3.53 GiB [ 1.922905] mmc1: SDHCI controller on 10230000.sdhci1 [10230000.sdhci1] using ADMA 64-bit [ 1.924090] mmcblk0boot0: mmc0:0001 M65704 partition 1 2.00 MiB [ 1.933408] usbcore: registered new interface driver usbhid [ 1.939825] mmcblk0boot1: mmc0:0001 M65704 partition 2 2.00 MiB [ 1.945251] usbhid: USB HID core driver [ 1.946125] NET: Registered protocol family 10 [ 1.952043] mmcblk0rpmb: mmc0:0001 M65704 partition 3 512 KiB, chardev (248:0) [ 1.956983] Segment Routing with IPv6 [ 1.963634] mmcblk0: p1 p2 [ 1.969311] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.973424] mmcblk0: p2 size 30468096 extends beyond EOD, truncated [ 1.976911] NET: Registered protocol family 17 [ 1.995122] Key type dns_resolver registered [ 2.000809] registered taskstats version 1 [ 2.005419] Loading compiled-in X.509 certificates [ 2.022814] mcom03-pcie 2000000.pcie: host bridge /sdr@1900000/pcie@0/pcie@2000000 ranges: [ 2.032108] mcom03-pcie 2000000.pcie: No bus range found for /sdr@1900000/pcie@0/pcie@2000000, using [bus 00-ff] [ 2.043740] mcom03-pcie 2000000.pcie: Parsing ranges property... [ 2.050486] mcom03-pcie 2000000.pcie: MEM 0x400000000..0x4ffffffff -> 0x00000000 [ 2.059142] mcom03-pcie 2000000.pcie: DMA 0x0000000000000000..0x000000027fffffff -> 0x0000000800000000 [ 2.069788] mcom03-pcie 2000000.pcie: DMA 0x0000000400000000..0x000000057fffffff -> 0x0000000c00000000 [ 2.087346] mmc1: new high speed SDHC card at address 0001 [ 2.094594] mmcblk1: mmc1:0001 SD16G 14.6 GiB [ 2.101690] mmcblk1: p1 p2 [ 7.082893] mcom03-pcie 2000000.pcie: Phy link never came up [ 7.089522] mcom03-pcie 2000000.pcie: PCI host bridge to bus 0000:00 [ 7.096711] pci_bus 0000:00: root bus resource [bus 00-ff] [ 7.102908] pci_bus 0000:00: root bus resource [mem 0x400000000-0x4ffffffff] (bus address [0x00000000-0xffffffff]) [ 7.114531] pci_bus 0000:00: scanning bus [ 7.119109] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400 [ 7.125972] pci 0000:00:00.0: reg 0x10: [mem 0x400000000-0x400000fff] [ 7.133255] pci 0000:00:00.0: reg 0x14: [mem 0x400000000-0x400000fff] [ 7.140494] pci 0000:00:00.0: reg 0x38: [mem 0x400000000-0x40000ffff pref] [ 7.148500] pci 0000:00:00.0: supports D1 [ 7.153037] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 7.159491] pci 0000:00:00.0: PME# disabled [ 7.170810] pci_bus 0000:00: fixups for bus [ 7.175562] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0 [ 7.183377] pci_bus 0000:01: scanning bus [ 7.193619] pci_bus 0000:01: fixups for bus [ 7.198314] pci_bus 0000:01: bus scan returning with max=01 [ 7.204619] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1 [ 7.212187] pci_bus 0000:00: bus scan returning with max=ff [ 7.218507] pci 0000:00:00.0: BAR 6: assigned [mem 0x400000000-0x40000ffff pref] [ 7.226837] pci 0000:00:00.0: BAR 0: assigned [mem 0x400010000-0x400010fff] [ 7.234686] pci 0000:00:00.0: BAR 1: assigned [mem 0x400011000-0x400011fff] [ 7.242534] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 7.248752] pcieport 0000:00:00.0: of_irq_parse_pci: failed with rc=-22 [ 7.256208] pcieport 0000:00:00.0: assign IRQ: got 0 [ 7.262432] pcieport 0000:00:00.0: Signaling PME with IRQ 58 [ 7.269106] pcieport 0000:00:00.0: AER enabled with IRQ 58 [ 7.276043] hctosys: unable to open rtc device (rtc0) [ 7.282450] ttyS0 - failed to request DMA [ 7.289160] Freeing unused kernel memory: 832K [ 7.294215] Run /init as init process [ 7.547695] INITRAMFS: version 2.31.0 [ 7.595489] INIT: Entering runlevel: 3 [ 7.662068] Parsing cmdline arguments: [ DONE ] [ 8.296250] Creating /etc/fstab: [ DONE ] [ 8.496677] Mounting filesystem [/dev]: [ DONE ] [ 8.654260] Mounting filesystem [/sys]: [ DONE ] [ 8.931195] Mounting filesystem [/run]: [ DONE ] [ 9.327051] Setting kernel runtime parameters: [ DONE ] [ 9.522532] Loading modules: [ DONE ] [ 9.738346] Starting udevd service: [ DONE ] [ 10.333372] Starting plymouthd service: [ DONE ] [ 10.786659] Starting ueventd service: [ DONE ] [ 11.202683] Starting polld service: [ DONE ] [ 16.584946] Network up (lo): [ DONE ] [ 17.523614] INIT: Entering runlevel: 2 [ 18.384366] Stopping polld service: [ DONE ] [ 19.737983] Stopping ueventd service: [ DONE ] [ 20.097410] Stopping udevd service: [ DONE ] [ 20.465721] Moving filesystem [/dev]: [ DONE ] [ 20.727691] Moving filesystem [/run]: [ DONE ] [ 21.060420] Unmounting filesystem [/sys]: [ DONE ] [ 21.545295] Asking all remaining processes to terminate: [ DONE ] [ 21.838127] INIT: Running init (/sbin/init) Welcome to ALT Starterkit 10 (Hypericum)! [ OK ] Created slice Slice /system/getty. [ OK ] Created slice Slice /system/modprobe. [ OK ] Created slice Slice /system/serial-getty. [ OK ] Created slice User and Session Slice. [ OK ] Set up automount Arbitrary…s File System Automount Point. [ OK ] Reached target Preparation for Network. [ OK ] Reached target Remote Encrypted Volumes. [ OK ] Reached target Slice Units. [ OK ] Reached target Swaps. [ OK ] Reached target Local Verity Protected Volumes. [ OK ] Listening on initctl Compatibility Named Pipe. [ OK ] Listening on Journal Audit Socket. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket. [ OK ] Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on User Database Manager Socket. Mounting Huge Pages File System... Mounting POSIX Message Queue File System... Mounting Kernel Debug File System... Mounting Kernel Trace File System... Starting Create List of Static Device Nodes... Starting Load Kernel Module configfs... Starting Load Kernel Module dm_mod... Starting Load Kernel Module drm... Starting Load Kernel Module efi_pstore... Starting Load Kernel Module fuse... Starting Load Kernel Module loop... Starting File System Check on Root Device... Starting Journal Service... Starting Load Kernel Modules... Starting Coldplug All udev Devices... Starting Setup Virtual Console... [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted Kernel Trace File System. [ OK ] Finished Create List of Static Device Nodes. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module dm_mod. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module efi_pstore. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module loop. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Create Static Device Nodes in /dev... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load Kernel Modules. Starting Apply Kernel Variables... [ OK ] Started Journal Service. [ OK ] Finished Coldplug All udev Devices. Starting Wait for udev To …plete Device Initialization... [ OK ] Finished Apply Kernel Variables. [ OK ] Finished File System Check on Root Device. [ OK ] Finished Create Static Device Nodes in /dev. Starting Remount Root and Kernel File Systems... [ OK ] Finished Remount Root and Kernel File Systems. [ OK ] Reached target Preparation for Local File Systems. Mounting /tmp... Starting Flush Journal to Persistent Storage... [ OK ] Reached target Remote File Systems. Starting Load/Save Random Seed... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Setup Virtual Console. [ OK ] Mounted /tmp. [ OK ] Reached target Local File Systems. Starting Tell Plymouth To Write Out Runtime Data... [ OK ] Finished Tell Plymouth To Write Out Runtime Data. Starting User Database Manager... [ OK ] Started User Database Manager. [ OK ] Finished Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Started Forward Password R…s to Plymouth Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Finished Create Volatile Files and Directories. Starting Record System Boot/Shutdown in UTMP... [ OK ] Finished Record System Boot/Shutdown in UTMP. [ OK ] Found device /dev/ttyS0. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Wait for udev To Complete Device Initialization. [ OK ] Reached target System Initialization. [ OK ] Started CUPS Scheduler. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Path Units. [ OK ] Reached target Timer Units. [ OK ] Listening on Alterator backend server (socket). [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on CUPS Scheduler. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Socket Units. [ OK ] Reached target Basic System. [ OK ] Started Alterator backend server. Starting Avahi mDNS/DNS-SD Stack... Starting NTP client/server... [ OK ] Started D-Bus System Message Bus. Starting Network Connectivity... Starting Authorization Manager... Starting User Login Management... Starting Preparing video drivers... [ OK ] Finished Preparing video drivers. [ OK ] Started NTP client/server. [ OK ] Started Network Connectivity. Starting Network Manager... [ OK ] Started User Login Management. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Network Manager. [ OK ] Reached target Network. Starting CUPS Scheduler... Starting OpenSSH server daemon... Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Vixie Cron Daemon. Starting Light Display Manager... Starting Hold until boot process finishes up... Starting Hostname Service... [ OK ] Started Hostname Service. localhost login: root Password: Last login: Fri Apr 28 15:20:00 +05 2023 on ttyS0 [root@localhost ~]# uname -r 4.19.106-g1aec3ec6b [root@localhost ~]# uname -a Linux localhost.localdomain 4.19.106-g1aec3ec6b #244 SMP Sun Apr 21 19:47:29 UTC 2024 aarch64 GNU/Linux [root@localhost ~]# mount /dev/mmcblk1p1 /mnt [root@localhost ~]# /mnt/coremark-mt.exe 2K performance run parameters for coremark. CoreMark Size : 666 Total ticks : 15720 Total time (secs): 15.720000 Iterations/Sec : 15267.175573 Iterations : 240000 Compiler version : GCC8.2.1 20180802 Compiler flags : -O2 -DMULTITHREAD=4 -DUSE_FORK -DPERFORMANCE_RUN=1 -lrt Parallel Fork : 4 Memory location : Please put data memory location here (e.g. code in flash, data on heap etc) seedcrc : 0xe9f5 [0]crclist : 0xe714 [1]crclist : 0xe714 [2]crclist : 0xe714 [3]crclist : 0xe714 [0]crcmatrix : 0x1fd7 [1]crcmatrix : 0x1fd7 [2]crcmatrix : 0x1fd7 [3]crcmatrix : 0x1fd7 [0]crcstate : 0x8e3a [1]crcstate : 0x8e3a [2]crcstate : 0x8e3a [3]crcstate : 0x8e3a [0]crcfinal : 0xbd59 [1]crcfinal : 0xbd59 [2]crcfinal : 0xbd59 [3]crcfinal : 0xbd59 Correct operation validated. See README.md for run and reporting rules. CoreMark 1.0 : 15267.175573 / GCC8.2.1 20180802 -O2 -DMULTITHREAD=4 -DUSE_FORK -DPERFORMANCE_RUN=1 -lrt / Heap / 4:Fork [root@localhost ~]# [root@localhost ~]# [root@localhost ~]# /mnt/stream_c_arm64.exe ------------------------------------------------------------- STREAM version $Revision: 5.10 $ ------------------------------------------------------------- This system uses 8 bytes per array element. ------------------------------------------------------------- Array size = 10000000 (elements), Offset = 0 (elements) Memory per array = 76.3 MiB (= 0.1 GiB). Total memory required = 228.9 MiB (= 0.2 GiB). Each kernel will be executed 10 times. The *best* time for each kernel (excluding the first iteration) will be used to compute the reported bandwidth. ------------------------------------------------------------- Number of Threads requested = 4 Number of Threads counted = 4 ------------------------------------------------------------- Your clock granularity/precision appears to be 1 microseconds. Each test below will take on the order of 49240 microseconds. (= 49240 clock ticks) Increase the size of the arrays if this shows that you are not getting at least 20 clock ticks per test. ------------------------------------------------------------- WARNING -- The above is only a rough guideline. For best results, please be sure you know the precision of your system timer. ------------------------------------------------------------- Function Best Rate MB/s Avg time Min time Max time Copy: 4680.8 0.034825 0.034182 0.035504 Scale: 4388.4 0.037486 0.036460 0.039076 Add: 3709.0 0.065521 0.064707 0.066482 Triad: 3697.0 0.065945 0.064917 0.067434 ------------------------------------------------------------- Solution Validates: avg error less than 1.000000e-13 on all three arrays ------------------------------------------------------------- [root@localhost ~]# [root@localhost ~]# [root@localhost ~]# dd if=/dev/mmcblk1 of=/dev/null bs=81920 status=progress iflag=direct 29573120 bytes (30 MB, 28 MiB) copied, 8 s, 3.7 MB/s 379+0 records in 378+0 records out 30965760 bytes (31 MB, 30 MiB) copied, 8.40034 s, 3.7 MB/s [root@localhost ~]# [root@localhost ~]# [root@localhost ~]# dd if=/dev/mmcblk0 of=/dev/null bs=81920 status=progress iflag=direct 1549598720 bytes (1.5 GB, 1.4 GiB) copied, 19 s, 81.6 MB/s 19915+0 records in 19914+0 records out 1631354880 bytes (1.6 GB, 1.5 GiB) copied, 20.0007 s, 81.6 MB/s [root@localhost ~]# cat /proc/cpuinfo processor : 0 BogoMIPS : 54.00 Features : fp asimd crc32 cpuid CPU implementer : 0x41 CPU architecture: 8 CPU variant : 0x0 CPU part : 0xd03 CPU revision : 4 processor : 1 BogoMIPS : 54.00 Features : fp asimd crc32 cpuid CPU implementer : 0x41 CPU architecture: 8 CPU variant : 0x0 CPU part : 0xd03 CPU revision : 4 processor : 2 BogoMIPS : 54.00 Features : fp asimd crc32 cpuid CPU implementer : 0x41 CPU architecture: 8 CPU variant : 0x0 CPU part : 0xd03 CPU revision : 4 processor : 3 BogoMIPS : 54.00 Features : fp asimd crc32 cpuid CPU implementer : 0x41 CPU architecture: 8 CPU variant : 0x0 CPU part : 0xd03 CPU revision : 4 [root@localhost ~]#