ddrinit: d56ea12 Ranks: 1 Die size: 0 Rank size: 13 MB Full size: 13 MB Full SDRAM Width: 0 bits Primary SDRAM Width: 0 bits ECC SDRAM Width: 0 bits Device Width: 8 bits Number of Row Addresses: 65536 Number of Column Addresses: 1024 Number of Bank Addresses: 8 Bank Group Addressing: 1 Clock Cycle Time (tCK): 1071 ps Minimum Clock Cycle Time (tCK min): 0 ps Maximum Clock Cycle Time (tCK max): 0 ps CAS# Latency Time (tAA min): 21420 ps Minimum Four Activate Windows Delay (tFAW): 40698 ps RAS to CAS Delay Time (tRCD min): 18207 ps Row Precharge Delay Time (tRP min): 18207 ps Active to Precharge Delay Time (tRAS min): 42840 ps Normal Refresh Recovery Delay Time (tRFC1 min): 0 ps 2x Mode Refresh Recovery Delay Time (tRFC2 min): 0 ps 4x Mode Refresh Recovery Delay Time (tRFC4 min): 0 ps Short Row Active to Row Active Delay (tRRD_S min): 10710 ps Long Row Active to Row Active Delay (tRRD_L min): 0 ps Long CAS to CAS Delay Time (tCCD_L min): 0 ps Minimum Active to Auto-Refresh Delay (tRC): 59976 ps DDRMC0: Initialized successfully within 1410723 us, 1 ranks, speed 1867 MT/s Ranks: 1 Die size: 0 Rank size: 13 MB Full size: 13 MB Full SDRAM Width: 0 bits Primary SDRAM Width: 0 bits ECC SDRAM Width: 0 bits Device Width: 8 bits Number of Row Addresses: 65536 Number of Column Addresses: 1024 Number of Bank Addresses: 8 Bank Group Addressing: 1 Clock Cycle Time (tCK): 1071 ps Minimum Clock Cycle Time (tCK min): 0 ps Maximum Clock Cycle Time (tCK max): 0 ps CAS# Latency Time (tAA min): 21420 ps Minimum Four Activate Windows Delay (tFAW): 40698 ps RAS to CAS Delay Time (tRCD min): 18207 ps Row Precharge Delay Time (tRP min): 18207 ps Active to Precharge Delay Time (tRAS min): 42840 ps Normal Refresh Recovery Delay Time (tRFC1 min): 0 ps 2x Mode Refresh Recovery Delay Time (tRFC2 min): 0 ps 4x Mode Refresh Recovery Delay Time (tRFC4 min): 0 ps Short Row Active to Row Active Delay (tRRD_S min): 10710 ps Long Row Active to Row Active Delay (tRRD_L min): 0 ps Long CAS to CAS Delay Time (tCCD_L min): 0 ps Minimum Active to Auto-Refresh Delay (tRC): 59976 ps DDRMC1: Initialized successfully within 1404133 us, 1 ranks, speed 1867 MT/s Total DDR memory size 4096 MiB Memory interleaving: 4 KiB, 2-channel NOTICE: BL31: v2.6(release):v2.5-887-g9566c09d4 NOTICE: BL31: Built : 12:17:21, Feb 2 2023 U-Boot 2021.01-00010-g96fa1e41f9 (Apr 05 2024 - 15:03:13 +0000) Model: RanetkaPC SBC v1.1 DRAM: 3.3 GiB CPU: Setting CPU frequency to 1188000000 (PLL mult: 43)...done. drivers/i2c/designware_i2c.c:779-designware_i2c_ofdata_to_platdata() i2c_designware i2c@1730000: Can't get reset: -2 PMIC: Failed to read digipot, ret: -121 PMIC: Core voltage set to: 905mV (0x21) drivers/i2c/designware_i2c.c:779-designware_i2c_ofdata_to_platdata() i2c_designware i2c@1710000: Can't get reset: -2 HDMI: Failed to read adv7513, ret: -121 HDMI: adv7513 enabled WDT: Started with servicing (120s timeout) MMC: sdhci0@10220000: 0, sdhci1@10230000: 1 Loading Environment from SPIFlash... SF: Detected w25q128fw with page size 256 Bytes, erase size 4 KiB, total 16 MiB OK Display: Arm Mali DP550 r0p2 malidp_setup_timings: product = DP550, reg_val = 0x10031050, HSYNCPOL = 2, VSYNCPOL = 8 display_enable: panel_bpp = 8, timing.hactive = 800, timing.vactive = 600, pixelclock = 49500000 sdhci_send_command: Timeout for status update! mmc_init: -110, time 1007 Error: could not access storage. In: serial0@1750000 Out: serial Err: serial Net: Warning: ethernet@10200000 (eth0) using random MAC address - 7e:64:8e:ab:7f:3f eth0: ethernet@10200000 Hit any key to stop autoboot: 0 starting USB... Bus dwc3@10000000: usb dr_mode not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Bus dwc3@10100000: usb dr_mode not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus dwc3@10000000 for devices... 2 USB Device(s) found scanning bus dwc3@10100000 for devices... 4 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 4.19.106/ 29116 coremark-arm32-mt.exe 27540 coremark-arm32.exe 29456 coremark-mt.exe 28960 coremark.exe 12962268 initrd.img 132150 splash.bmp 23096 stream_c_arm64.exe 6.6.107/ 7 file(s), 2 dir(s) Booting from USB 38645 bytes read in 14 ms (2.6 MiB/s) 24766472 bytes read in 771 ms (30.6 MiB/s) 12962268 bytes read in 362 ms (34.1 MiB/s) ## Flattened Device Tree blob at 898c00000 Booting using the fdt blob at 0x898c00000 Loading Ramdisk to 89dd51000, end 89ea51000 ... OK Loading Device Tree to 000000089dd44000, end 000000089dd506f4 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.6.107-ga13bf874da85 (wit@devbox) (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 8.2-2018-08 (arm-rel-8.23)) 8.2.1 20180802, GNU ld (GNU Toolchain for the A-profile Architecture 8.2-2018-08 (arm-rel-8.23)) 2.30.0.20180625) #66 SMP Wed Jul 8 10:14:35 UTC 2026 [ 0.000000] Machine model: MCom-03 KERAutomation SMARC devboard [ 0.000000] earlycon: uart0 at MMIO32 0x0000000001750000 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000890000000-0x00000008ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000900000000-0x000000095fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000890000000-0x000000095fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000890000000-0x000000095fffffff] [ 0.000000] cma: Reserved 256 MiB at 0x000000089ec00000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 29 pages/cpu s78376 r8192 d32216 u118784 [ 0.000000] pcpu-alloc: s78376 r8192 d32216 u118784 alloc=29*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyS0,115200 consoleblank=0 vt.global_cursor_default=0 vt.cur_default=1 earlyprintk=ttyS0,115200 earlycon splash plymouth.ignore-serial-consoles root=/dev/sda2 rootwait ro fsck.mode=auto fsck.repair=yes init=/sbin/init rdinit=/init loglevel=8 net.ifnames=0 fbcon=logo-pos:center fbcon=logo-count:1 video=${video_hdmi} [ 0.000000] Unknown kernel command line parameters "earlyprintk=ttyS0,115200", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 838656 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: mapped [mem 0x00000008fbfff000-0x00000008fffff000] (64MB) [ 0.000000] Memory: 2974652K/3407872K available (12608K kernel code, 2106K rwdata, 4488K rodata, 4864K init, 405K bss, 171076K reserved, 262144K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 42722 entries in 167 pages [ 0.000000] ftrace: allocated 167 pages with 5 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 128 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000001180000 [ 0.000000] ITS [mem 0x01120000-0x0113ffff] [ 0.000000] ITS@0x0000000001120000: allocated 131072 Devices @900200000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x00000009001b0000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000009001c0000 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. ERROR: mcom03_sip_handler: unhandled SMC (0xc2000003) [ 0.000000] Media power domain: Board firmware does not support power domain control [ 0.000000] Media power domain is initialized ERROR: mcom03_sip_handler: unhandled SMC (0xc2000003) [ 0.000000] SDR power domain: Board firmware does not support power domain control [ 0.000000] SDR power domain is initialized [ 0.000000] arch_timer: cp15 timer(s) running at 27.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x63a1e71a3, max_idle_ns: 440795203123 ns [ 0.000001] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 4398046511093ns [ 0.009395] Console: colour dummy device 80x25 [ 0.014333] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=270000) [ 0.025703] pid_max: default: 32768 minimum: 301 [ 0.030972] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.039122] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.050094] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.060229] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.070623] rcu: Hierarchical SRCU implementation. [ 0.075874] rcu: Max phase no-delay instances is 1000. [ 0.082417] Platform MSI: msi-controller@1120000 domain created [ 0.089084] PCI/MSI: /interrupt-controller@1100000/msi-controller@1120000 domain created [ 0.098343] smp: Bringing up secondary CPUs ... [ 0.114000] Detected VIPT I-cache on CPU1 [ 0.114073] GICv3: CPU1: found redistributor 1 region 0:0x00000000011a0000 [ 0.114100] GICv3: CPU1: using allocated LPI pending table @0x00000009001d0000 [ 0.114159] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.124900] Detected VIPT I-cache on CPU2 [ 0.124948] GICv3: CPU2: found redistributor 2 region 0:0x00000000011c0000 [ 0.124970] GICv3: CPU2: using allocated LPI pending table @0x00000009001e0000 [ 0.125004] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.135691] Detected VIPT I-cache on CPU3 [ 0.135744] GICv3: CPU3: found redistributor 3 region 0:0x00000000011e0000 [ 0.135767] GICv3: CPU3: using allocated LPI pending table @0x00000009001f0000 [ 0.135799] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.135900] smp: Brought up 1 node, 4 CPUs [ 0.221345] SMP: Total of 4 processors activated. [ 0.226500] CPU features: detected: 32-bit EL0 Support [ 0.232138] CPU features: detected: CRC32 instructions [ 0.237850] CPU: All CPU(s) started at EL2 [ 0.242350] alternatives: applying system-wide alternatives [ 0.250699] devtmpfs: initialized [ 0.261385] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.272201] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.289256] pinctrl core: initialized pinctrl subsystem [ 0.296492] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.304480] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.312308] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.320862] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.329592] audit: initializing netlink subsys (disabled) [ 0.335749] audit: type=2000 audit(0.250:1): state=initialized audit_enabled=0 res=1 [ 0.336511] thermal_sys: Registered thermal governor 'step_wise' [ 0.344314] cpuidle: using governor menu [ 0.355439] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.362993] ASID allocator initialised with 65536 entries [ 0.375279] mcom03-media-pinctrl media-bus:media-pinctrl: 15 pins & 1 groups registered [ 0.386586] mcom03-lsperiph-pinctrl 1680000.urb:lsperiph0-pinctrl: 32 pins & 0 groups registered [ 0.400129] /hsperiph-bus/urb@10400000/hsperiph-pinctrl: Fixed dependency cycle(s) with /hsperiph-bus/urb@10400000/hsperiph-pinctrl/emac-v18 [ 0.413987] /hsperiph-bus/urb@10400000/hsperiph-pinctrl: Fixed dependency cycle(s) with /hsperiph-bus/urb@10400000/hsperiph-pinctrl/hsperiph-misc-default [ 0.429530] mcom03-hsperiph-pinctrl 10400000.urb:hsperiph-pinctrl: 91 pins & 23 groups registered [ 0.447400] mcom03-lsperiph-pinctrl 17e0000.urb:lsperiph1-pinctrl: 32 pins & 1 groups registered [ 0.459546] Modules: 26608 pages in range for non-PLT usage [ 0.459555] Modules: 518128 pages in range for PLT usage [ 0.466681] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.479967] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page [ 0.486860] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages [ 0.494299] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page [ 0.501183] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.508623] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.515501] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages [ 0.522942] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page [ 0.531266] iommu: Default domain type: Translated [ 0.536517] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.543418] SCSI subsystem initialized [ 0.547695] usbcore: registered new interface driver usbfs [ 0.553751] usbcore: registered new interface driver hub [ 0.559612] usbcore: registered new device driver usb [ 0.565696] pps_core: LinuxPPS API ver. 1 registered [ 0.571136] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.581171] PTP clock support registered [ 0.586852] vgaarb: loaded [ 0.592311] clocksource: Switched to clocksource arch_sys_counter [ 1.045224] NET: Registered PF_INET protocol family [ 1.050904] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 1.061859] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 1.071263] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.079831] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 1.088748] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) [ 1.098022] TCP: Hash tables configured (established 32768 bind 32768) [ 1.105334] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 1.112767] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 1.120793] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.127539] RPC: Registered named UNIX socket transport module. [ 1.134046] RPC: Registered udp transport module. [ 1.139200] RPC: Registered tcp transport module. [ 1.144365] RPC: Registered tcp-with-tls transport module. [ 1.150375] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.157456] PCI: CLS 0 bytes, default 64 [ 1.162014] Unpacking initramfs... [ 1.167118] Initialise system trusted keyrings [ 1.172222] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 1.179739] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.186644] NFS: Registering the id_resolver key type [ 1.192220] Key type id_resolver registered [ 1.196833] Key type id_legacy registered [ 1.201951] Key type asymmetric registered [ 1.206476] Asymmetric key parser 'x509' registered [ 1.211913] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.220389] io scheduler mq-deadline registered [ 1.225405] io scheduler kyber registered [ 1.229880] io scheduler bfq registered [ 1.244406] irq_elvees_qlic 1fe00000.interrupt-controller: Initialized successfully [ 1.255256] irq_elvees_qlic 1940000.interrupt-controller: Initialized successfully [ 1.266962] gpio-dwapb 1610000.gpio: initialized pinmux driver for port A [ 1.275822] gpio-dwapb 1610000.gpio: initialized pinmux driver for port B [ 1.283960] gpio-dwapb 1610000.gpio: initialized pinmux driver for port C [ 1.292212] gpio-dwapb 1610000.gpio: initialized pinmux driver for port D [ 1.301421] gpio-dwapb 1780000.gpio: initialized pinmux driver for port A [ 1.309879] gpio-dwapb 1780000.gpio: initialized pinmux driver for port B [ 1.318139] gpio-dwapb 1780000.gpio: initialized pinmux driver for port C [ 1.326354] gpio-dwapb 1780000.gpio: initialized pinmux driver for port D ERROR: mcom03_sip_handler: unhandled SMC (0xc2000004) ERROR: mcom03_sip_handler: unhandled SMC (0xc2000004) [ 1.348682] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.358584] printk: console [ttyS0] disabled [ 1.363793] 1750000.serial: ttyS0 at MMIO 0x1750000 (irq = 32, base_baud = 1745028) is a 16550A [ 1.373471] printk: console [ttyS0] enabled [ 1.373471] printk: console [ttyS0] enabled [ 1.382882] printk: bootconsole [uart0] disabled [ 1.382882] printk: bootconsole [uart0] disabled [ 1.400323] tun: Universal TUN/TAP device driver, 1.6 [ 1.407173] (unnamed net_device) (uninitialized): Using gen_pool sram-pool@0 for DMA descriptors [ 1.407274] arasan-gemac 10200000.ethernet (unnamed net_device) (uninitialized): Using random hw address [ 1.427808] arasan-gemac 10200000.ethernet (unnamed net_device) (uninitialized): Set clk_1588 freq to 125 MHz [ 1.449860] arasan-gemac 10200000.ethernet eth0: Arasan GEMAC Ethernet at 0x10200000 int=33 (f6:c3:11:47:c0:28) [ 1.462514] (unnamed net_device) (uninitialized): Using gen_pool sram-pool@0 for DMA descriptors [ 1.462612] arasan-gemac 10210000.ethernet (unnamed net_device) (uninitialized): Using random hw address [ 1.483133] arasan-gemac 10210000.ethernet (unnamed net_device) (uninitialized): Set clk_1588 freq to 125 MHz [ 1.505093] arasan-gemac 10210000.ethernet eth1: Arasan GEMAC Ethernet at 0x10210000 int=34 (92:ac:58:2b:ef:84) [ 1.517031] usbcore: registered new device driver r8152-cfgselector [ 1.524154] usbcore: registered new interface driver r8152 [ 1.541817] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.548065] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 1.556865] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe6d hci version 0x110 quirks 0x0000008000000010 [ 1.567503] xhci-hcd xhci-hcd.0.auto: irq 35, io mem 0x10000000 [ 1.574380] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.580547] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 1.589211] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 1.596865] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06 [ 1.606176] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.614317] usb usb1: Product: xHCI Host Controller [ 1.619782] usb usb1: Manufacturer: Linux 6.6.107-ga13bf874da85 xhci-hcd [ 1.627296] usb usb1: SerialNumber: xhci-hcd.0.auto [ 1.633550] hub 1-0:1.0: USB hub found [ 1.637812] hub 1-0:1.0: 1 port detected [ 1.642822] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.652042] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.06 [ 1.656386] Initramfs unpacking failed: invalid magic at start of compressed archive [ 1.661323] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.676375] Freeing initrd memory: 13312K [ 1.678026] usb usb2: Product: xHCI Host Controller [ 1.687928] usb usb2: Manufacturer: Linux 6.6.107-ga13bf874da85 xhci-hcd [ 1.695427] usb usb2: SerialNumber: xhci-hcd.0.auto [ 1.701596] hub 2-0:1.0: USB hub found [ 1.705839] hub 2-0:1.0: 1 port detected [ 1.710872] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.717036] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 1.725822] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe6d hci version 0x110 quirks 0x0000008000000010 [ 1.736412] xhci-hcd xhci-hcd.1.auto: irq 36, io mem 0x10100000 [ 1.743251] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.749389] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 1.757965] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 1.765461] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06 [ 1.774726] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.782819] usb usb3: Product: xHCI Host Controller [ 1.788272] usb usb3: Manufacturer: Linux 6.6.107-ga13bf874da85 xhci-hcd [ 1.795769] usb usb3: SerialNumber: xhci-hcd.1.auto [ 1.801675] hub 3-0:1.0: USB hub found [ 1.805911] hub 3-0:1.0: 1 port detected [ 1.810717] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.819933] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.06 [ 1.829184] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.837276] usb usb4: Product: xHCI Host Controller [ 1.842738] usb usb4: Manufacturer: Linux 6.6.107-ga13bf874da85 xhci-hcd [ 1.850229] usb usb4: SerialNumber: xhci-hcd.1.auto [ 1.856125] hub 4-0:1.0: USB hub found [ 1.860344] hub 4-0:1.0: 1 port detected [ 1.865355] usbcore: registered new interface driver uas [ 1.871389] usbcore: registered new interface driver usb-storage [ 1.878979] i2c_dev: i2c /dev entries driver [ 1.884145] mr75202 1f050000.pvt: Configure TS SDA clock: 1031250 Hz, div = 24 [ 1.892224] mr75202 1f050000.pvt: Configure VM SDA clock: 1031250 Hz, div = 24 [ 1.911604] hwmon hwmon0: temp2_input not attached to any thermal zone [ 1.918998] hwmon hwmon0: temp3_input not attached to any thermal zone [ 1.926379] hwmon hwmon0: temp4_input not attached to any thermal zone [ 1.933690] mr75202 1f050000.pvt: 4 temperature sensors [ 1.939531] mr75202 1f050000.pvt: 4 voltage sensors [ 1.942367] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 1.946591] sdhci: Secure Digital Host Controller Interface driver [ 1.959190] sdhci: Copyright(c) Pierre Ossman [ 1.964071] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.970746] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.978662] usbcore: registered new interface driver usbhid [ 1.984907] usbhid: USB HID core driver [ 1.989914] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 2.000762] NET: Registered PF_INET6 protocol family [ 2.002334] mmc1: SDHCI controller on 10230000.sdhci1 [10230000.sdhci1] using ADMA 64-bit [ 2.002771] mmc0: SDHCI controller on 10220000.sdhci0 [10220000.sdhci0] using ADMA 64-bit [ 2.007391] Segment Routing with IPv6 [ 2.028731] In-situ OAM (IOAM) with IPv6 [ 2.033214] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.040377] NET: Registered PF_PACKET protocol family [ 2.046081] Bridge firewalling registered [ 2.050621] 8021q: 802.1Q VLAN Support v1.8 [ 2.055372] Key type dns_resolver registered [ 2.067349] registered taskstats version 1 [ 2.072091] Loading compiled-in X.509 certificates [ 2.092403] usb 3-1: new high-speed USB device number 2 using xhci-hcd [ 2.103743] gpio-dwapb 1610000.gpio: Bypass pinmux request: Mux pin0 on port A for IRQ purposes [ 2.118088] VDDb: Bringing 900000uV into 937500-937500uV [ 2.132546] rk808-rtc rk808-rtc.4.auto: registered as rtc0 [ 2.139237] rk808-rtc rk808-rtc.4.auto: setting system clock to 2013-01-18T08:50:26 UTC (1358499026) [ 2.145338] usb 1-1: New USB device found, idVendor=1005, idProduct=b113, bcdDevice= 1.10 [ 2.152673] mcom03-pcie 2000000.pcie: Using embedded MSI interrupt-controller [ 2.158609] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.166767] mcom03-pcie 2000000.pcie: host bridge /sdr-bus/mcom03-pcie-bus/pcie@2000000 ranges: [ 2.174553] usb 1-1: Product: USB FLASH DRIVE [ 2.184266] mcom03-pcie 2000000.pcie: No bus range found for /sdr-bus/mcom03-pcie-bus/pcie@2000000, using [bus 00-ff] [ 2.189123] usb 1-1: SerialNumber: 070D57C89F00DB34 [ 2.201229] mcom03-pcie 2000000.pcie: MEM 0x0400000000..0x04efffffff -> 0x0010000000 [ 2.207581] usb-storage 1-1:1.0: USB Mass Storage device detected [ 2.215862] mcom03-pcie 2000000.pcie: IB MEM 0x0840000000..0x0abfffffff -> 0x0040000000 [ 2.223125] scsi host0: usb-storage 1-1:1.0 [ 2.231767] mcom03-pcie 2000000.pcie: IB MEM 0x0c00000000..0x0d7fffffff -> 0x0400000000 [ 2.275190] mmc0: error -84 whilst initialising MMC card [ 2.282550] usb 3-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3 [ 2.291695] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.341436] hub 3-1:1.0: USB hub found [ 2.345709] hub 3-1:1.0: 4 ports detected [ 2.362574] mcom03-pcie 2000000.pcie: Failed to allocate 32-bit MSI address [ 2.370499] mcom03-pcie 2000000.pcie: iATU: unroll T, 32 ob, 32 ib, align 4K, limit 1024G [ 2.376945] mmc0: error -84 whilst initialising MMC card [ 2.493574] mmc0: error -84 whilst initialising MMC card [ 2.641980] mmc0: error -84 whilst initialising MMC card [ 2.649225] mmc0: Failed to initialize a non-removable card [ 2.722330] usb 3-1.1: new full-speed USB device number 3 using xhci-hcd [ 2.869456] usb 3-1.1: New USB device found, idVendor=0403, idProduct=6015, bcdDevice=10.00 [ 2.878811] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.886992] usb 3-1.1: Product: FT230X Basic UART [ 2.892251] usb 3-1.1: Manufacturer: FTDI [ 2.896741] usb 3-1.1: SerialNumber: DK0EOPY7 [ 3.002329] usb 3-1.2: new full-speed USB device number 4 using xhci-hcd [ 3.139448] usb 3-1.2: New USB device found, idVendor=0403, idProduct=6015, bcdDevice=10.00 [ 3.148797] usb 3-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.156978] usb 3-1.2: Product: FT230X Basic UART [ 3.162237] usb 3-1.2: Manufacturer: FTDI [ 3.166727] usb 3-1.2: SerialNumber: DK0EOPXW [ 3.264460] scsi 0:0:0:0: Direct-Access USB FLASH DRIVE PMAP PQ: 0 ANSI: 6 [ 3.379995] mcom03-pcie 2000000.pcie: Phy link never came up [ 3.386838] mcom03-pcie 2000000.pcie: PCI host bridge to bus 0000:00 [ 3.393957] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.400094] pci_bus 0000:00: root bus resource [mem 0x400000000-0x4efffffff] (bus address [0x10000000-0xffffffff]) [ 3.411735] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400 [ 3.418485] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff] [ 3.425516] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x00000fff] [ 3.432547] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref] [ 3.440218] pci 0000:00:00.0: supports D1 [ 3.444711] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 3.453640] pci 0000:00:00.0: BAR 6: assigned [mem 0x400000000-0x40000ffff pref] [ 3.461261] sd 0:0:0:0: [sda] 121145344 512-byte logical blocks: (62.0 GB/57.8 GiB) [ 3.461911] pci 0000:00:00.0: BAR 0: assigned [mem 0x400010000-0x400010fff] [ 3.471939] sd 0:0:0:0: [sda] Write Protect is off [ 3.478255] pci 0000:00:00.0: BAR 1: assigned [mem 0x400011000-0x400011fff] [ 3.483612] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00 [ 3.491390] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 3.498231] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 3.503693] pcieport 0000:00:00.0: PME: Signaling with IRQ 57 [ 3.519910] pcieport 0000:00:00.0: AER: enabled with IRQ 57 [ 3.522372] sda: sda1 sda2 [ 3.526344] mcom03-pcie 2000000.pcie: 'reset-gpio' isn't specified in PCIe node [ 3.529644] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 3.537427] mcom03-pcie 2000000.pcie: Assume untested PCIx_PERSTN pad is in use [ 3.537437] mcom03-pcie 2000000.pcie: Redirecting MSI to 0x1130040 [ 3.559164] mcom03-pcie 2400000.pcie: Using embedded MSI interrupt-controller [ 3.567382] mcom03-pcie 2400000.pcie: host bridge /sdr-bus/mcom03-pcie-bus/pcie@2400000 ranges: [ 3.577126] mcom03-pcie 2400000.pcie: No bus range found for /sdr-bus/mcom03-pcie-bus/pcie@2400000, using [bus 00-ff] [ 3.589238] mcom03-pcie 2400000.pcie: MEM 0x0600000000..0x06efffffff -> 0x0010000000 [ 3.598479] mcom03-pcie 2400000.pcie: IB MEM 0x0840000000..0x0abfffffff -> 0x0040000000 [ 3.607672] mcom03-pcie 2400000.pcie: IB MEM 0x0c00000000..0x0d7fffffff -> 0x0400000000 [ 3.732497] mcom03-pcie 2400000.pcie: Failed to allocate 32-bit MSI address [ 3.740423] mcom03-pcie 2400000.pcie: iATU: unroll T, 32 ob, 32 ib, align 4K, limit 1024G [ 4.749856] mcom03-pcie 2400000.pcie: Phy link never came up [ 4.756326] mcom03-pcie 2400000.pcie: PCI host bridge to bus 0001:00 [ 4.763434] pci_bus 0001:00: root bus resource [bus 00-ff] [ 4.769559] pci_bus 0001:00: root bus resource [mem 0x600000000-0x6efffffff] (bus address [0x10000000-0xffffffff]) [ 4.781188] pci 0001:00:00.0: [16c3:abcd] type 01 class 0x060400 [ 4.787942] pci 0001:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff] [ 4.794973] pci 0001:00:00.0: reg 0x14: [mem 0x00000000-0x00000fff] [ 4.801995] pci 0001:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref] [ 4.809671] pci 0001:00:00.0: supports D1 [ 4.814163] pci 0001:00:00.0: PME# supported from D0 D1 D3hot [ 4.823126] pci 0001:00:00.0: BAR 6: assigned [mem 0x600000000-0x60000ffff pref] [ 4.831397] pci 0001:00:00.0: BAR 0: assigned [mem 0x600010000-0x600010fff] [ 4.839197] pci 0001:00:00.0: BAR 1: assigned [mem 0x600011000-0x600011fff] [ 4.846998] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 4.853605] pcieport 0001:00:00.0: PME: Signaling with IRQ 61 [ 4.860340] pcieport 0001:00:00.0: AER: enabled with IRQ 61 [ 4.866772] mcom03-pcie 2400000.pcie: 'reset-gpio' isn't specified in PCIe node [ 4.874962] mcom03-pcie 2400000.pcie: Assume untested PCIx_PERSTN pad is in use [ 4.883141] mcom03-pcie 2400000.pcie: Redirecting MSI to 0x1130040 [ 4.891518] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 1188000 KHz, changing to: 1377000 KHz [ 4.915805] clk: Disabling unused clocks [ 4.921259] dw-apb-uart 1750000.serial: forbid DMA for kernel console [ 4.933463] Freeing unused kernel memory: 4864K [ 4.938677] Run /init as init process [ 4.942797] with arguments: [ 4.946120] /init [ 4.948664] with environment: [ 4.952178] HOME=/ [ 4.954851] TERM=linux [ 4.957896] earlyprintk=ttyS0,115200 [ 5.083438] INITRAMFS: version 2.31.0 [ 5.155782] INIT: Entering runlevel: 3 [ 5.241003] Parsing cmdline arguments: [ DONE ] [ 5.843891] Creating /etc/fstab: [ DONE ] [ 6.074120] Mounting filesystem [/dev]: [ DONE ] [ 6.249752] Mounting filesystem [/sys]: [ DONE ] [ 6.538464] Mounting filesystem [/run]: [ DONE ] [ 6.989466] Setting kernel runtime parameters: [ DONE ] [ 7.221509] Loading modules: [ DONE ] [ 7.450733] Starting udevd service: [ DONE ] [ 8.134685] Starting plymouthd service: [ DONE ] [ 8.642693] Starting ueventd service: [ DONE ] [ 9.147295] Starting polld service: [ DONE ] [ 16.739568] Network up (lo): [ DONE ] [ 17.564140] INIT: Entering runlevel: 2 [ 17.932861] Stopping polld service: [ DONE ] [ 19.342820] Stopping ueventd service: [ DONE ] [ 19.740472] Stopping udevd service: [ DONE ] [ 20.131299] Moving filesystem [/dev]: [ DONE ] [ 20.414581] Moving filesystem [/run]: [ DONE ] [ 20.794393] Unmounting filesystem [/sys]: [ DONE ] [ 21.246203] Asking all remaining processes to terminate: [ DONE ] [ 21.506578] INIT: Running init (/sbin/init) Welcome to ALT Starterkit 10 (Hypericum)! [ OK ] Created slice Slice /system/getty. [ OK ] Created slice Slice /system/modprobe. [ OK ] Created slice Slice /system/serial-getty. [ OK ] Created slice User and Session Slice. [ OK ] Set up automount Arbitrary…s File System Automount Point. [ OK ] Reached target Preparation for Network. [ OK ] Reached target Remote Encrypted Volumes. [ OK ] Reached target Slice Units. [ OK ] Reached target Swaps. [ OK ] Reached target Local Verity Protected Volumes. [ OK ] Listening on initctl Compatibility Named Pipe. [ OK ] Listening on Journal Audit Socket. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket. [ OK ] Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on User Database Manager Socket. Mounting Huge Pages File System... Mounting POSIX Message Queue File System... Mounting Kernel Debug File System... Mounting Kernel Trace File System... Starting Create List of Static Device Nodes... Starting Load Kernel Module configfs... Starting Load Kernel Module dm_mod... Starting Load Kernel Module drm... Starting Load Kernel Module efi_pstore... Starting Load Kernel Module fuse... Starting Load Kernel Module loop... Starting File System Check on Root Device... Starting Journal Service... Starting Load Kernel Modules... Starting Coldplug All udev Devices... Starting Setup Virtual Console... [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted Kernel Trace File System. [ OK ] Finished Create List of Static Device Nodes. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module dm_mod. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module efi_pstore. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module loop. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Create Static Device Nodes in /dev... [ OK ] Mounted FUSE Control File System. [ OK ] Finished Load Kernel Modules. Starting Apply Kernel Variables... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Journal Service. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Coldplug All udev Devices. Starting Wait for udev To …plete Device Initialization... [ OK ] Finished File System Check on Root Device. [ OK ] Finished Setup Virtual Console. [ OK ] Finished Create Static Device Nodes in /dev. Starting Remount Root and Kernel File Systems... [FAILED] Failed to start Remount Root and Kernel File Systems. See 'systemctl status systemd-remount-fs.service' for details. [ OK ] Reached target Preparation for Local File Systems. Mounting /tmp... Starting Flush Journal to Persistent Storage... [ OK ] Reached target Remote File Systems. Starting Load/Save Random Seed... Starting Rule-based Manage…for Device Events and Files... [ OK ] Mounted /tmp. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Load/Save Random Seed. [ OK ] Reached target Local File Systems. Starting Tell Plymouth To Write Out Runtime Data... Starting Create Volatile Files and Directories... [ OK ] Finished Tell Plymouth To Write Out Runtime Data. Starting User Database Manager... [ OK ] Finished Create Volatile Files and Directories. Starting Record System Boot/Shutdown in UTMP... [ OK ] Started User Database Manager. [ OK ] Finished Record System Boot/Shutdown in UTMP. [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Started Forward Password R…s to Plymouth Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Reached target Path Units. [ OK ] Found device /dev/ttyS0. [ OK ] Finished Wait for udev To Complete Device Initialization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timer Units. [ OK ] Listening on Alterator backend server (socket). [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Socket Units. [ OK ] Reached target Basic System. [ OK ] Started Alterator backend server. Starting Avahi mDNS/DNS-SD Stack... Starting NTP client/server... [ OK ] Started D-Bus System Message Bus. Starting Network Connectivity... Starting Authorization Manager... Starting User Login Management... Starting Preparing video drivers... [ OK ] Finished Preparing video drivers. [ OK ] Started NTP client/server. [ OK ] Started User Login Management. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Network Connectivity. Starting Network Manager... [ OK ] Started Authorization Manager. Starting Modem Manager... [ OK ] Started Network Manager. [ OK ] Reached target Network. Starting OpenSSH server daemon... Starting Hostname Service... Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Vixie Cron Daemon. Starting Hold until boot process finishes up... Starting Terminate Plymouth Boot Screen... [ OK ] Finished Hold until boot process finishes up. [ OK ] Finished Terminate Plymouth Boot Screen. localhost login: root Password: [root@localhost ~]# [root@localhost ~]# [root@localhost ~]# [root@localhost ~]# [root@localhost ~]# [root@localhost ~]# cpupower Usage: cpupower [-d|--debug] [-c|--cpu cpulist ] [] Supported commands are: frequency-info frequency-set idle-info idle-set set info monitor help Not all commands can make use of the -c cpulist option. Use 'cpupower help ' for getting help for above commands. [root@localhost ~]# cpupower frequency-info analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 1 2 3 CPUs which need to have their frequency coordinated by software: 0 1 2 3 maximum transition latency: Cannot determine or is not supported. hardware limits: 378 MHz - 1.38 GHz available frequency steps: 378 MHz, 756 MHz, 1.16 GHz, 1.38 GHz available cpufreq governors: conservative ondemand userspace powersave performance schedutil current policy: frequency should be within 378 MHz and 1.38 GHz. The governor "ondemand" may decide which speed to use within this range. current CPU frequency: 378 MHz (asserted by call to hardware) [root@localhost ~]# dmesg | grep rk808 [ 2.132546] rk808-rtc rk808-rtc.4.auto: registered as rtc0 [ 2.139237] rk808-rtc rk808-rtc.4.auto: setting system clock to 2013-01-18T08:50:26 UTC (1358499026) [root@localhost ~]# dmesg | grep freq [ 0.014333] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=270000) [ 1.427808] arasan-gemac 10200000.ethernet (unnamed net_device) (uninitialized): Set clk_1588 freq to 125 MHz [ 1.483133] arasan-gemac 10210000.ethernet (unnamed net_device) (uninitialized): Set clk_1588 freq to 125 MHz [ 4.891518] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 1188000 KHz, changing to: 1377000 KHz [root@localhost ~]# [root@localhost ~]# [root@localhost ~]# [root@localhost ~]# mount /dev/sda1 /mnt [root@localhost ~]# /mnt/ 4.19.106/ coremark-arm32-mt.exe coremark-mt.exe initrd.img stream_c_arm64.exe 6.6.107/ coremark-arm32.exe coremark.exe splash.bmp [root@localhost ~]# /mnt/stream_c_arm64.exe ------------------------------------------------------------- STREAM version $Revision: 5.10 $ ------------------------------------------------------------- This system uses 8 bytes per array element. ------------------------------------------------------------- Array size = 10000000 (elements), Offset = 0 (elements) Memory per array = 76.3 MiB (= 0.1 GiB). Total memory required = 228.9 MiB (= 0.2 GiB). Each kernel will be executed 10 times. The *best* time for each kernel (excluding the first iteration) will be used to compute the reported bandwidth. ------------------------------------------------------------- Number of Threads requested = 4 Number of Threads counted = 4 ------------------------------------------------------------- Your clock granularity/precision appears to be 1 microseconds. Each test below will take on the order of 38098 microseconds. (= 38098 clock ticks) Increase the size of the arrays if this shows that you are not getting at least 20 clock ticks per test. ------------------------------------------------------------- WARNING -- The above is only a rough guideline. For best results, please be sure you know the precision of your system timer. ------------------------------------------------------------- Function Best Rate MB/s Avg time Min time Max time Copy: 5871.1 0.027528 0.027252 0.027968 Scale: 5766.2 0.028837 0.027748 0.029714 Add: 4973.3 0.048864 0.048258 0.049551 Triad: 4810.1 0.050869 0.049895 0.051679 ------------------------------------------------------------- Solution Validates: avg error less than 1.000000e-13 on all three arrays ------------------------------------------------------------- [root@localhost ~]# /mnt/stream_c_arm64.exe ------------------------------------------------------------- STREAM version $Revision: 5.10 $ ------------------------------------------------------------- This system uses 8 bytes per array element. ------------------------------------------------------------- Array size = 10000000 (elements), Offset = 0 (elements) Memory per array = 76.3 MiB (= 0.1 GiB). Total memory required = 228.9 MiB (= 0.2 GiB). Each kernel will be executed 10 times. The *best* time for each kernel (excluding the first iteration) will be used to compute the reported bandwidth. ------------------------------------------------------------- Number of Threads requested = 4 Number of Threads counted = 4 ------------------------------------------------------------- Your clock granularity/precision appears to be 1 microseconds. Each test below will take on the order of 37600 microseconds. (= 37600 clock ticks) Increase the size of the arrays if this shows that you are not getting at least 20 clock ticks per test. ------------------------------------------------------------- WARNING -- The above is only a rough guideline. For best results, please be sure you know the precision of your system timer. ------------------------------------------------------------- Function Best Rate MB/s Avg time Min time Max time Copy: 5889.1 0.027417 0.027169 0.027669 Scale: 5707.9 0.028752 0.028031 0.029678 Add: 4956.8 0.048875 0.048418 0.049507 Triad: 4850.1 0.050392 0.049484 0.051267 ------------------------------------------------------------- Solution Validates: avg error less than 1.000000e-13 on all three arrays ------------------------------------------------------------- [root@localhost ~]# /mnt/stream_c_arm64.exe ------------------------------------------------------------- STREAM version $Revision: 5.10 $ ------------------------------------------------------------- This system uses 8 bytes per array element. ------------------------------------------------------------- Array size = 10000000 (elements), Offset = 0 (elements) Memory per array = 76.3 MiB (= 0.1 GiB). Total memory required = 228.9 MiB (= 0.2 GiB). Each kernel will be executed 10 times. The *best* time for each kernel (excluding the first iteration) will be used to compute the reported bandwidth. ------------------------------------------------------------- Number of Threads requested = 4 Number of Threads counted = 4 ------------------------------------------------------------- Your clock granularity/precision appears to be 1 microseconds. Each test below will take on the order of 37921 microseconds. (= 37921 clock ticks) Increase the size of the arrays if this shows that you are not getting at least 20 clock ticks per test. ------------------------------------------------------------- WARNING -- The above is only a rough guideline. For best results, please be sure you know the precision of your system timer. ------------------------------------------------------------- Function Best Rate MB/s Avg time Min time Max time Copy: 5884.9 0.027493 0.027188 0.027946 Scale: 5799.4 0.028401 0.027589 0.029590 Add: 4928.0 0.049016 0.048701 0.049774 Triad: 4755.0 0.051039 0.050473 0.052497 ------------------------------------------------------------- Solution Validates: avg error less than 1.000000e-13 on all three arrays ------------------------------------------------------------- [root@localhost ~]# /mnt/stream_c_arm64.exe ------------------------------------------------------------- STREAM version $Revision: 5.10 $ ------------------------------------------------------------- This system uses 8 bytes per array element. ------------------------------------------------------------- Array size = 10000000 (elements), Offset = 0 (elements) Memory per array = 76.3 MiB (= 0.1 GiB). Total memory required = 228.9 MiB (= 0.2 GiB). Each kernel will be executed 10 times. The *best* time for each kernel (excluding the first iteration) will be used to compute the reported bandwidth. ------------------------------------------------------------- Number of Threads requested = 4 Number of Threads counted = 4 ------------------------------------------------------------- Your clock granularity/precision appears to be 1 microseconds. Each test below will take on the order of 37796 microseconds. (= 37796 clock ticks) Increase the size of the arrays if this shows that you are not getting at least 20 clock ticks per test. ------------------------------------------------------------- WARNING -- The above is only a rough guideline. For best results, please be sure you know the precision of your system timer. ------------------------------------------------------------- Function Best Rate MB/s Avg time Min time Max time Copy: 5918.9 0.027371 0.027032 0.027648 Scale: 5777.9 0.029598 0.027692 0.032088 Add: 5009.6 0.048697 0.047908 0.049411 Triad: 4769.7 0.050757 0.050318 0.051224 ------------------------------------------------------------- Solution Validates: avg error less than 1.000000e-13 on all three arrays ------------------------------------------------------------- [root@localhost ~]# /mnt/coremark-mt.exe 2K performance run parameters for coremark. CoreMark Size : 666 Total ticks : 13213 Total time (secs): 13.213000 Iterations/Sec : 18163.929463 Iterations : 240000 Compiler version : GCC8.2.1 20180802 Compiler flags : -O2 -DMULTITHREAD=4 -DUSE_FORK -DPERFORMANCE_RUN=1 -lrt Parallel Fork : 4 Memory location : Please put data memory location here (e.g. code in flash, data on heap etc) seedcrc : 0xe9f5 [0]crclist : 0xe714 [1]crclist : 0xe714 [2]crclist : 0xe714 [3]crclist : 0xe714 [0]crcmatrix : 0x1fd7 [1]crcmatrix : 0x1fd7 [2]crcmatrix : 0x1fd7 [3]crcmatrix : 0x1fd7 [0]crcstate : 0x8e3a [1]crcstate : 0x8e3a [2]crcstate : 0x8e3a [3]crcstate : 0x8e3a [0]crcfinal : 0xbd59 [1]crcfinal : 0xbd59 [2]crcfinal : 0xbd59 [3]crcfinal : 0xbd59 Correct operation validated. See README.md for run and reporting rules. CoreMark 1.0 : 18163.929463 / GCC8.2.1 20180802 -O2 -DMULTITHREAD=4 -DUSE_FORK -DPERFORMANCE_RUN=1 -lrt / Heap / 4:Fork [root@localhost ~]# /mnt/coremark-mt.exe 2K performance run parameters for coremark. CoreMark Size : 666 Total ticks : 13210 Total time (secs): 13.210000 Iterations/Sec : 18168.054504 Iterations : 240000 Compiler version : GCC8.2.1 20180802 Compiler flags : -O2 -DMULTITHREAD=4 -DUSE_FORK -DPERFORMANCE_RUN=1 -lrt Parallel Fork : 4 Memory location : Please put data memory location here (e.g. code in flash, data on heap etc) seedcrc : 0xe9f5 [0]crclist : 0xe714 [1]crclist : 0xe714 [2]crclist : 0xe714 [3]crclist : 0xe714 [0]crcmatrix : 0x1fd7 [1]crcmatrix : 0x1fd7 [2]crcmatrix : 0x1fd7 [3]crcmatrix : 0x1fd7 [0]crcstate : 0x8e3a [1]crcstate : 0x8e3a [2]crcstate : 0x8e3a [3]crcstate : 0x8e3a [0]crcfinal : 0xbd59 [1]crcfinal : 0xbd59 [2]crcfinal : 0xbd59 [3]crcfinal : 0xbd59 Correct operation validated. See README.md for run and reporting rules. CoreMark 1.0 : 18168.054504 / GCC8.2.1 20180802 -O2 -DMULTITHREAD=4 -DUSE_FORK -DPERFORMANCE_RUN=1 -lrt / Heap / 4:Fork [root@localhost ~]# [root@localhost ~]# [root@localhost ~]# [root@localhost ~]# ifcnfig -bash: ifcnfig: command not found [root@localhost ~]# ifconfig eth0 Link encap:Ethernet HWaddr D6:76:19:56:6E:0B inet addr:192.168.78.100 Bcast:192.168.78.255 Mask:255.255.255.0 inet6 addr: fe80::af2:e1ef:a987:8c0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:71 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:986 (986.0 b) TX bytes:8273 (8.0 KiB) Interrupt:33 eth1 Link encap:Ethernet HWaddr D6:C6:FB:BE:4E:81 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:34 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:15 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2398 (2.3 KiB) TX bytes:2398 (2.3 KiB) [root@localhost ~]# iperf3 -c 192.168.169.6 - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr iperf3: interrupt - the client has terminated [root@localhost ~]# iperf3 -c 192.168.78.1 Connecting to host 192.168.78.1, port 5201 [ 5] local 192.168.78.100 port 54850 connected to 192.168.78.1 port 5201 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.01 sec 112 MBytes 929 Mbits/sec 0 154 KBytes [ 5] 1.01-2.01 sec 112 MBytes 942 Mbits/sec 0 154 KBytes [ 5] 2.01-3.01 sec 109 MBytes 916 Mbits/sec 0 154 KBytes [ 5] 3.01-4.01 sec 112 MBytes 941 Mbits/sec 0 154 KBytes [ 5] 4.01-5.01 sec 112 MBytes 942 Mbits/sec 0 154 KBytes [ 5] 5.01-6.00 sec 111 MBytes 942 Mbits/sec 0 154 KBytes [ 5] 6.00-7.01 sec 112 MBytes 940 Mbits/sec 0 154 KBytes [ 5] 7.01-8.01 sec 112 MBytes 939 Mbits/sec 0 154 KBytes [ 5] 8.01-9.00 sec 111 MBytes 942 Mbits/sec 0 154 KBytes [ 5] 9.00-10.01 sec 112 MBytes 940 Mbits/sec 0 154 KBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.01 sec 1.09 GBytes 937 Mbits/sec 0 sender [ 5] 0.00-10.01 sec 1.09 GBytes 937 Mbits/sec receiver iperf Done. [root@localhost ~]# iperf3 -c 192.168.78.1 -R Connecting to host 192.168.78.1, port 5201 Reverse mode, remote host 192.168.78.1 is sending [ 5] local 192.168.78.100 port 48288 connected to 192.168.78.1 port 5201 [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 106 MBytes 891 Mbits/sec [ 5] 1.00-2.00 sec 113 MBytes 946 Mbits/sec [ 5] 2.00-3.00 sec 113 MBytes 946 Mbits/sec [ 5] 3.00-4.00 sec 113 MBytes 946 Mbits/sec [ 5] 4.00-5.00 sec 113 MBytes 945 Mbits/sec [ 5] 5.00-6.00 sec 113 MBytes 946 Mbits/sec [ 5] 6.00-7.00 sec 113 MBytes 946 Mbits/sec [ 5] 7.00-8.00 sec 113 MBytes 946 Mbits/sec [ 5] 8.00-9.00 sec 112 MBytes 943 Mbits/sec [ 5] 9.00-10.00 sec 113 MBytes 945 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.01 sec 1.10 GBytes 941 Mbits/sec 440 sender [ 5] 0.00-10.00 sec 1.09 GBytes 940 Mbits/sec receiver iperf Done. [root@localhost ~]#